Final Products –Test method and Product Standards

BS EN 40-7:2002  Lighting columns. Requirements for fibre reinforced polymer composite lighting columns.

BS EN 1013-2:1999  Light transmitting profiled plastics sheeting for single skin roofing.  Specific requirements and test methods for sheets of glass fibre reinforced polyester resin (GRP).

BS EN 1115  Plastics piping systems for underground drainage and sewerage under pressure. Glass-reinforced thermosetting plastics (GRP) based on unsaturated polyester resin (UP). General

BS EN 12445  Transportable gas cylinders. Fully wrapped composite cylinders

BS EN 12457  Transportable gas cylinders. Seamless, hoop-wrapped composite cylinders

BS EN 13280:2001  Specification for glass fibre reinforced cisterns of one-piece and sectional construction, for the storage, above ground, of cold water (replaces BS 7491 3 parts)

BS 4154:1985. Corrugated plastics translucent sheets from thermo-setting polyester resin (glass fibre reinforced). 

BS 5480:1990.  Specification for glass fibre reinforced plastics (GRP) pipes and fittings for water supply or sewerage. 

ISO 7370. Glass fibre reinforced thermosetting plastics (GRP) pipes and fittings; nominal diameters, specified diameters and standard lengths.

ISO/FDIS 7432 Glass reinforced thermosetting plastics (GRP) pipes and fittings-test methods to prove the design of locked socket and spigot joints

BS 7491.  Glass fibre reinforced plastics cisterns for cold water storage

ISO/DIS 7509 Plastics piping systems – glass reinforced thermosetting plastics (GRP) pipes – determination of time to failure under sustained internal pressure

ISO 7510. Plastics piping systems- glass reinforced plastics (GRP) components

ISO 7511. Plastics piping systems – glass reinforced thermosetting plastics (GRP) pipes and fittings – test methods to prove the leak tightness of the wall under short-term internal pressure.

ISO 7684. Plastics piping systems – glass reinforced thermosetting plastics (GRP) pipes – determination of the creep factor under dry conditions.

ISO 7685. Plastics piping systems - glass reinforced thermosetting plastics (GRP) pipes – determination of initial specific ring stiffness.

ISO/DIS 8483 Glass reinforced thermosetting plastics (GRP) pipes and fittings – test methods to prove the design of bolted flange joints.

ISO/DIS 8513. Plastics piping systems - glass reinforced thermosetting plastics (GRP) pipes – determination of initial longitudinal tensile properties.

ISO 8521 Plastics piping systems - glass reinforced thermosetting plastics (GRP) pipes – determination of the apparent initial circumferential tensile strength.

ISO/DIS 8533. glass reinforced thermosetting plastics (GRP) pipes and fittings – test methods to prove the design of cemented or wrapped joints.

ISO/DIS 8639.  Glass reinforced thermosetting plastics (GRP) – test methods for leaktightness and resistance to damage of flexible and reduced-articulation joints.

ISO 10466.  Plastics piping systems - glass reinforced thermosetting plastics (GRP) pipes – test method to prove the resistance to initial ring deflection.

ISO/DIS 10467.  Plastics piping systems for pressure and non-pressure sewerage – glass reinforced thermosetting plastics (GRP) based on unsaturated polyester (UP) resin.

ISO/DIS 10468 plastics piping systems - glass reinforced thermosetting plastics (GRP) pipes – determination of the long-term specific creep stiffness under wet conditions and calculation of the wet creep factor.

ISO/DIS 10471. Plastics piping systems - glass reinforced thermosetting plastics (GRP) pipes – determination of the long-term ultimate bending strain and the long-term ultimate relative ring deflection under wet conditions.

ISO/DIS 10639. Plastics piping systems for water supply with or without pressure – glass reinforced plastics (GRP) based on unsaturated polyester (UP) resin.

ISO 10928. Plastics piping systems - glass reinforced thermosetting plastics (GRP) pipes and fittings – methods for regression analysis and their use.

ISO 10952. Plastics piping systems - glass reinforced thermosetting plastics (GRP) pipes and fittings – determination of the resistance to chemical attack from the inside of a section in a deflected condition

ISO 11119-1:2002. Gas cylinders of composite construction -- Specification and test methods -- Part 1: Hoop wrapped composite gas cylinders (available in English only)

ISO 11119-2:2002  Gas cylinders of composite construction -- Specification and test methods -- Part 2: Fully wrapped fibre reinforced composite gas cylinders with load-sharing metal liners (available in English only)

ISO 11119-3:2002  Gas cylinders of composite construction -- Specification and test methods -- Part 3: Fully wrapped fibre reinforced composite gas cylinders with non-load-sharing metallic or non-metallic liners

EN 13706: Fibre reinforced plastics – Specification for pultruded profiles

prEN 13923. Filament-wound GRP pressure vessels. Materials, design, manufacture and testing

ISO 14692:2002. Petroleum and natural gas industries - GRP piping  (4 Parts)

ISO/DIS 14828. Plastics piping systems - glass reinforced thermosetting plastics (GRP) pipes – determination of the long-term specific ring relaxation stiffness under wet conditioned and calculation of the wet relaxation factor